Choose a transaction and write a Batch Input program with 'Call Transaction'. Do not use the Messagetab feature of 'Call Transaction'. In this case the last error message will be at the SY-MSG* system fields. Recreate the complete error message from table T100! (This example is also used by the demonstration of SY-MSG* system fields)
Solution:
REPORT ZSYSTEM LINE-SIZE 255.
TABLES: T100.
* Batch-input data
DATA: BEGIN OF G_BDCDATA OCCURS 100.
INCLUDE STRUCTURE BDCDATA.
DATA: END OF G_BDCDATA.
DATA: G_MESSAGE(200).
PERFORM FILL_BDCDATA.
CALL TRANSACTION 'FI01' USING G_BDCDATA MODE 'N'.
* of course it is nicer with a message itab, but this example
* should also demostrate the use of system variables.
SELECT SINGLE * FROM T100 WHERE
SPRSL = 'E'
AND ARBGB = SY-MSGID
AND MSGNR = SY-MSGNO.
G_MESSAGE = T100-TEXT.
PERFORM REPLACE_PARAMETERS USING SY-MSGV1
SY-MSGV2
SY-MSGV3
SY-MSGV4
CHANGING G_MESSAGE.
WRITE: / 'System variables:'.
SKIP.
WRITE: / ' Sy-msgty:', SY-MSGTY.
WRITE: / ' Sy-msgid:', SY-MSGID.
WRITE: / ' Sy-msgno:', SY-MSGNO.
WRITE: / ' Sy-msgv1:', SY-MSGV1.
WRITE: / ' Sy-msgv2:', SY-MSGV2.
WRITE: / ' Sy-msgv3:', SY-MSGV3.
WRITE: / ' Sy-msgv4:', SY-MSGV4.
SKIP.
WRITE: / 'The transaction was called with a wrong country code.'.
WRITE: / 'The error message should be either that or that you have'.
WRITE: / ' no authorisation to execute the transaction'.
SKIP.
WRITE: / 'Message:'.
SKIP.
WRITE: / SY-MSGTY, G_MESSAGE.
*---------------------------------------------------------------------*
* Build up the BDC-table *
*---------------------------------------------------------------------*
FORM FILL_BDCDATA.
REFRESH G_BDCDATA.
PERFORM BDC_DYNPRO USING 'SAPMF02B' '0100'.
PERFORM BDC_FIELD USING 'BNKA-BANKS' 'ZZZ'.
PERFORM BDC_FIELD USING 'BDC_OKCODE' 'QQQQQ'.
ENDFORM.
*---------------------------------------------------------------------*
* FORM BDC_DYNPRO *
*---------------------------------------------------------------------*
* Batchinput: Start new Dynpro *
*---------------------------------------------------------------------*
FORM REPLACE_PARAMETERS USING P_PAR_1
P_PAR_2
P_PAR_3
P_PAR_4
CHANGING P_MESSAGE.
* erst mal pruefen, ob numerierte Parameter verwendet wurden
DO.
REPLACE '&1' WITH P_PAR_1 INTO P_MESSAGE.
IF SY-SUBRC <> 0.
EXIT.
ENDIF.
ENDDO.
DO.
REPLACE '&2' WITH P_PAR_2 INTO P_MESSAGE.
IF SY-SUBRC <> 0.
EXIT.
ENDIF.
ENDDO.
DO.
REPLACE '&3' WITH P_PAR_3 INTO P_MESSAGE.
IF SY-SUBRC <> 0.
EXIT.
ENDIF.
ENDDO.
DO.
REPLACE '&4' WITH P_PAR_4 INTO P_MESSAGE.
IF SY-SUBRC <> 0.
EXIT.
ENDIF.
ENDDO.
* falls keine numerierten Parameter vorh., ersetzen wie gehabt
REPLACE '&' WITH P_PAR_1 INTO P_MESSAGE.
CONDENSE P_MESSAGE.
IF SY-SUBRC EQ 0.
REPLACE '&' WITH P_PAR_2 INTO P_MESSAGE.
CONDENSE P_MESSAGE.
IF SY-SUBRC EQ 0.
REPLACE '&' WITH P_PAR_3 INTO P_MESSAGE.
CONDENSE P_MESSAGE.
IF SY-SUBRC EQ 0.
REPLACE '&' WITH P_PAR_4 INTO P_MESSAGE.
CONDENSE P_MESSAGE.
ENDIF.
ENDIF.
ENDIF.
ENDFORM. "replace_parameters
